Thomas COVID Supplier BadgeDisplaysResourcesCOVID-19 SUPPLIESGalleryGet a Quote

Delrin® 525GR is a 25% glass reinforced acetal homopolymer for injection molding. It has very high strength, stiffness, and high deflection temperature, and excellent creep resistance. Delrin® is the crystalline thermoplastic of choice for impact and wear resistance in a wide range of industrial and mechanical applications. With low, consistent internal stress, the material is easily machined and fabricated, experiencing little dimensional change during machining and use.

澳洲幸运10历史开奖

Contact us today for your fabrication and machining needs!

Request Fabrication/Machining Services
At a Glance

Generic Name
Polyoxymethylene, Polyacetal

Available In
Resin

Start Your Quote

Send us a message:

*Required Fields

Gallery

澳洲幸运10预测软件下载

Stock Products Properties Applications Advantages

澳洲幸运10号码开奖

Give us your cut-to-size dimensions. We will precision-cut these plastics to your exact size. Additional sizes and colors available upon request.

澳洲幸运10人工计划软件

Physical PropertiesUnitsASTMResults
Density kg/m3 (g/cm3 ) ISO 1183 1600 (1.60)
Mechanical PropertiesUnitsASTMResults
Tensile Strength MPa (kpsi) ASTM D 638 5mm/min (0.2in/min) - 151 (21.9)
Elongation at Break % ASTM D 638 5mm/min (0.2in/min) - 3.2
Tensile Modulus MPa (kpsi) ASTM D 638 5mm/min (0.2in/min) - 9000 (1310)
Flexural Modulus MPa (kpsi) ASTM D 790 8000 (1160)
Izod Impact J/m (ft lb/in) ASTM D 256 96 (1.8)
Unnotched Impact J/m (ft lb/in) ASTM D 4812 1100 (20.6)
Thermal PropertiesUnitsASTMResults
Heat Deflection Temperature °C (°F) ASTM D 648
0.45MPa (66psi), Not Annealed 177 (351)
1.8MPa (264psi), Not Annealed 173 (344)
CLTE, Parallel ASTM E 831 E-4/C
23 - 55C (73 - 130F) 0.29
CLTE, Normal ASTM E 831 E-4/C
23 - 55C (73 - 130F) 0.83
Electrical PropertiesUnitsASTMResults
Surface Resistivity ohm ASTM D 257 2 E15
Volume Resistivity ohm cm ASTM D 257 4 E13
Dielectric Strength, Short Time kV/mm (V/mil) ASTM D 149
3.2mm (0.126in) 17.3 (440)
Dielectric Constant ASTM D 150
1E6 Hz 3.8
Dissipation Factor ASTM D 150
1E6 Hz 0.0076

NOTE: The property values presented above are typical values intended for reference and comparison purposes only. They should NOT be used as a basis for design specifications or quality control. Contact us for manufacturers’ complete material property datasheets. All values at 73°F (23°C) unless otherwise noted.

澳洲幸运10精准预测

  • Automotive

澳洲幸运10现场开奖结果

  • Creep Resistance
  • Weldable
  • Homopolymer
Copyright © 2016 - 2022 Emco Industrial Plastics
秒速赛车在线平台 SG飞艇最新开奖结果 极速赛车分析软件 极速飞艇单双 极速赛车开奖号码 秒速飞艇公式 秒速赛车开奖历史表